|
DELTA JT160 Shopmaster 10 Amp 6-Inch Benchtop Jointer | 
| Brand: DELTA
Category: Home Improvement
List Price: $483.00
Buy New: $239.99
as of 11/23/2009 19:14 CST details
You Save: $243.01 (50%)
New (11) Used (1) from $226.99
Seller: Amazon.com
Rating:  72 reviews
Media: Tools & Hardware
Autographed: No
Memorabilia: No
Shipping Weight (lbs): 41.5
Dimensions (in): 33 x 13 x 11.5
MPN: JT160
Model: JT160
UPC: 069554001604
EAN: 0069554001604
Shipping: Eligible for FREE Super Saver Shipping
Availability: Usually ships in 24 hours
| |
| Features:
| • | Powerful 10 Amp motor features variable speeds between 6,000 and 11,000 RPM | | • | Efficient two-knife cutterhead is easily adjustable | | • | Extra-large table provides support for up to 6-inch wide stock | | • | Measures 30 x 18 x 13.5 inches (LxWxH) and weighs 35 pounds | | • | Includes push blocks and wrenches |
|
| Accessories:
|
| Similar Items:
| |
| Editorial Reviews:
Amazon.com Product Description
The DELTA JT160 Shopmaster 10 Amp 6-Inch Benchtop Jointer uses a variable speed motor and two-knife cutterhead configuration with jack-screw knife leveling arrangement for easy replacement and adjustments. The 30 x 6-3/16 inch table provides support for surfacing stock up to six inches wide, including soft woods, hard woods, and plastics. The speedy 10 Amp motor spins at 6,000-11,000 RPM, which makes the dual-cutter turn at 12,000-22,000 CPM. The center-mounted fence provides ample support throughout the cut for precise edge jointing, and it tilts out at 45 degrees for added versatility.
|
| Customer Reviews:
Showing reviews 1-5 of 72
 Owned for 7 years - still going strong! October 21, 2009
javajunki
Excellent benchtop jointer. We purchased this about 7 years ago and it is still going strong. There are bigger ones, more expenssive models and those with a more bells and whistles but this is a great price, solid build and does what it is meant to do...for seven years. Completely satisfied with the purchase and recommend to anyone in need of a decent priced performer.
 DISASTER June 30, 2009
Larry Weaver (SOUTH PADRE IS, TX)
1 out of 1 found this review helpful
I WENT THROUGH FOUR UNITS IN A PERIOD OF 2 WEEKS AND NONE OF THEM OPERATED PROPERLY. THEY EITHER CUT A TAPER OR PUT A LOW SPOT IN THE MIDDLE OF THE BOARD ELIMINATING ANY KIND OF AN ACCEPTABLE JOINT. ALL FOUR UNITS WERE TAKEN TO THE LOCAL DELTA FACTORY SERVICE FACILITY WHERE IT WAS DETERMINED THAT THEY COULD NOT BE REPAIRED. THERE IS NO ADJUSTMENT ON EITHER TABLE OTHER THAN ELEVATION ON THE INFEED TABLE. ALL OF THE UNITS HAD ONE OR BOTH TABLES THAT WERE WARPED OR HAD UNEVENLY MACHINED MOUNTING BOSSES. THE OTHER PROBLEM WAS A FLIMSLY FENCE AND HORIZONTAL/VERTICAL ADJ. KNOBS THAT INTERFERE WITH EACH OTHER. I HAD NO PROBLEM GETTING REPLACEMENTS OR IN THE CASE OF THE LAST UNIT, A REFUND.
 JT160 jointer May 21, 2009
Raybert C. Griffin Jr.
Tool is fairly good for a jointer in this price range. it is powerfull enough to plain 6" rock maple without stalling (although at minimium stock removal)
 Delta JT160 Shopmaster March 13, 2009
L. E. (Austin, TX)
Good on small to mid size projects.
Nice speed controls. A bit loud on high speed but not too bad- wear protection.
Needed to be shimmed... November 23, 2008
Jonathan C. Magee
1 out of 1 found this review helpful
I have a few Delta tools and I was surprised of the poor "accuracy" of this product. The in feed table was not completely flat with the outfeed table at zero clearance and needed to be shimmed in order to get an accurate "flat" jointed edge; disappointed to say the least from a Delta tool. All in all, after the hassle during set up with the shimming, it does have decent construction and provides as a good small shop jointer for under $300.
Showing reviews 1-5 of 72
|
|
|
CERTAIN CONTENT THAT APPEARS ON THIS SITE COMES FROM AMAZON SERVICES LLC. THIS CONTENT IS PROVIDED ‘AS IS’ AND IS SUBJECT TO CHANGE OR REMOVAL AT ANY TIME. Thanks for shopping with us! | |
